SCUMM/V5 opcodes

SCUMM V5 opcodes

The following conventions are used in the encoding descriptions.

opcode	The instruction's opcode, with the appropriate bits set according to the parameters.
result	A result pointer. (A standard word pointer, always a LE word.)
value[8]	An 8-bit constant (a byte).
value[16]	A 16-bit constant (a word LE).
value[p8]	An 8-bit parameter. This may be encoded as a word LE if it's a pointer, or a byte if it's a constant.
value[p16]	A 16-bit parameter. This is always encoded as a word LE.
value[v16]	A variable number of word LE parameters. These are encoded as a sequence of aux[8] param[p16]; param; aux contains the parameter bit to describe param. A byte of $FF terminates the sequence.
value[o]	The offset word for parameter value. This is only encoded if needed, but always at the position indicated. If not specified, the offset word occurs immediately after the parameter.
(term)	An optional term.

add ($5A)

Encoding

opcode result value[p16]

Operation

result := result + value

The variable pointed to by result is read, value is added to it, and the result written back.

and ($17)

one parameter, uses result

Encoding

opcode result value[p16]

Operation

result := result and value

The variable pointed to by result is read, logically ANDed with value, and the result written back.

arrayOp ($27)

parameters depend on auxilary opcode

Encoding

opcode $01 array[p8] opcode $02 dest[p8] src[p8] opcode $03 array[p8] index[p8] data[p8] opcode $04 result array[p8] index[p8] opcode $05 array[p8] size[p8]

Operation

Miscellaneous actions on Arrays (referred to by resource number).

Opcode	Meaning	Description
$01	load array	Ensures that the Array is loaded into memory. [I don't know what this does.]
$02	copy array	Creates a duplicate of src at resource number dest. The old Array at dest is lost.
$03	write entry	Writes the byte data at offset index of Array array. Out of bounds accesses cause undefined behaviour.
$04	read entry	Sets result to the byte of data at offset index of Array array. Out of bounds accesses cause undefined behaviour.
$05	create entry	Allocates or frees an Array. The Array array is initialised to size size; if size is zero, the Array is freed.

breakHere ($80)

no parameters

Encoding

opcode

Operation

Deschedules the currently running thread. Execution continues at the next instruction when the thread's next timeslot comes around.

chainScript ($42)

one parameter plus varargs

Encoding

opcode script[p8] args[v16]...

Operation

Replaces the currently running script with another one. The current script is terminated immediately and the new script, resource number script, is executed in the same thread. The new script has its local variables initialised to the list args. Uninitialised variables have undefined values.

debug ($6B)

one parameter, no result

Encoding

opcode param[p16]

Operation

Passes the parameter to the interpreter's debugger. What this does is entirely platform-specific (and may do nothing).

decrement ($C6)

no parameters, uses result

Encoding

opcode result

Operation

result := result - 1

Reads the variable pointed to by result, decrements it, and writes it back.

delay ($2E)

one constant parameter

Encoding

opcode param[24]

Operation

Suspends the current thread for the appropriate number of 1/60ths of a second. Yes, that really is a 24-bit LE constant.

delayVariable ($2E)

one constant parameter

Encoding

opcode pointer[16]

Operation

pointer is dereferenced and the current thread suspended for that number of 1/60ths of a second. Note that pointer is an inline constant, not a parameter.

divide ($5B)

one parameter, uses result

Encoding

opcode result value[p16]

Operation

result := result / value

The variable pointed to by result is read, divided by value, and the result written back. If value is zero, the result is undefined (and the interpeter may halt with an error).

drawBox ($3F)

two parameters, does not use result, supplementary opcode byte with three more subsequent parameters

Encoding

opcode left[p16] top[p16] auxopcode[8] right[p16] bottom[p16] colour[p8]

Operation

Draws a solid box on the backbuffer from (left, top)-(right, bottom) in the colour colour.

The only part of auxopcode that is relevant are the parameter bits. The rest of the opcode is ignored.

increment ($46)

no parameters, uses result

Encoding

opcode result

Operation

result := result + 1

Reads the variable pointed to by result, increments it, and writes it back.

jumpRelative ($18)

non-standard encoding

Encoding

opcode target[16]

Operation

PC := PC + target

The inline constant target is read as a signed word and added to the program counter after the instruction has been read. Therefore, if target is zero, the instruction will do nothing; if target is -3, an infinite loop will result.

or ($57)

one parameter, uses result

Encoding

opcode result value[p16]

Operation

result := result and value

The variable pointed to by result is read, logically ORed with value, and the result written back.

startScript ($0A)

one parameter plus varargs, extra encoding in opcode

Encoding

opcode script[p8] args[v16]...

Operation

Spawns a new thread running the code in script script. The new script has its local variables initialised to the list args. Uninitialised variables have undefined values.

The opcode carries extra information:

7	6	5	4 0
P1	Q	F	$0A

walkActorToObject ($36)

All material © 2000-2002 David Given, unless where stated otherwise.

Table of Parameters

This is a work in progress and is missing opcodes.

This table shows a summary of the opcodes and their parameters in a concise fashion. The information has been gleaned from the descumm source code, so some instruction names might not match those listed above.

Currently it is missing:

comparisons (lessThan, greaterThanEqual, equalZero etc)
drawObject
do_resource
do_if_state_code (comparisons)
do_print_ego
do_varset_code
do_unconditional_jump
loadRoomWithEgo
do_cursor_command
doSentence
do_expr_code
do_load_code_to_string (sub-opcode of 0x27)
do_actorops
do_pseudoRoom(buf)
do_room_ops(buf)
do_verbops(buf, opcode)
setVarRange
do_matrix_ops(buf, opcode)

Some instructions listed here are actually sub-opcodes, i.e. "WaitForCamera" is actually the "Wait" opcode with a sub-opcode representing "For Camera".

Argument types:

• V = variable
• B = byte
• W = word
• L = list
• J = jump (used by all boolean expressions, comparisons)
• D = delay; 24-bit constant (only used by delay, funnily enough)
• A = ASCII (0-terminated string?); used by "setObjectName"
• V|B or V|W = either a variable or a byte/word
• None, if it does not take that argument.

Instruction	Returns a Value	Arg 1	Arg 2	Arg 3
actorFollowCamera	False	V|B	None	None
actorFromPos	True	V|W	V|W	None
animateCostume	False	V|B	V|B	None
beginOverride	False	None	None	None
breakHere	False	None	None	None
chainScript	False	V|B	L	None
classOfIs	False	V|W	L	J
CopyString	False	V|B	V|B	None
CreateString	False	V|B	V|B	None
cutscene	False	L	None	None
debug?	False	V|W	None	None
delay	False	D	None	None
delayVariable	False	V	None	None
deleteVerbs	False	V|B	V|B	V|B
dummy	False	None	None	None
endCutscene	False	None	None	None
endOverride	False	None	None	None
faceActor	False	V|B	V|W	None
findInventory	True	V|B	V|B	None
findObject	True	V|W	V|W	None
freezeScripts	False	V|B	None	None
getActorCostume	True	V|B	None	None
getActorElevation	True	V|B	None	None
getActorFacing	True	V|B	None	None
getActorMoving	True	V|B	None	None
getActorRoom	True	V|B	None	None
getActorScale	True	V|B	None	None
getActorWalkBox	True	V|B	None	None
getActorWidth	True	V|B	None	None
getActorX	False	V|W	None	None
getActorY	False	V|W	None	None
getClosestObjActor	True	V|W	None	None
getDist	True	V|W	V|W	None
getInventoryCount	True	V|B	None	None
getObjectOwner	True	V|W	None	None
getObjectState	True	V|W	None	None
getRandomNr	True	V|B	None	None
GetStringChar	True	V|B	V|B	None
getStringWidth	True	V|B	None	None
getVerbEntryPoint	True	V|W	V|W	None
isActorInBox	False	V|B	V|B	J
isScriptRunning	True	V|B	None	None
isSoundRunning	True	V|B	None	None
lights	False	V|B	B	B
loadRoom	False	V|B	None	None
oldRoomEffect-fadein	False	V|W	None	None
oldRoomEffect-set	False	V|W	None	None
panCameraTo	False	V|W	None	None
pickupObject	False	V|W	V|B	None
putActor	False	V|B	V|W	V|W
putActorAtObject	False	V|B	V|W	None
putActorInRoom	False	V|B	V|B	None
restoreVerbs	False	V|B	V|B	V|B
saveLoadGame	True	V|B	None	None
saveVerbs	False	V|B	V|B	V|B
setCameraAt	False	V|W	None	None
setClass	False	V|W	L	None
setObjectName	False	V|W	A	None
setOwnerOf	False	V|W	V|B	None
setState	False	V|W	V|B	None
SetStringChar	False	V|B	V|B	V|B
soundKludge	False	L	None	None
startMusic	False	V|B	None	None
startObject	False	V|W	V|B	L
startScript	False	V|B	L	None
startSound	False	V|B	None	None
stopMusic	False	None	None	None
stopObjectCode	False	None	None	None
stopObjectScript	False	V|W	None	None
stopScript	False	V|B	None	None
stopSound	False	V|B	None	None
systemOps	False	B	None	None
WaitForActor	False	V|B	None	None
WaitForCamera	False	None	None	None
WaitForMessage	False	None	None	None
WaitForSentence	False	None	None	None
walkActorTo	False	V|B	V|W	V|W
walkActorToActor	False	V|B	V|B	B
walkActorToObject	False	V|B	V|W	None